How to Control Greenhouse Humidity to Prevent Botrytis in Cut Flowers
5 min read
Control greenhouse humidity by keeping petals and foliage dry overnight, coordinating heating with ventilation, and removing moisture sources around the crop. Fans, sensible irrigation and clean crop areas work together; no single humidity setting can guarantee flowers will stay free of Botrytis.
Pieter de Vries · first published · revised

Why Botrytis Loves a Damp Greenhouse
Botrytis cinerea, the fungus commonly associated with gray mold, thrives when plant surfaces remain wet or when the air around the canopy is persistently humid. In cut flowers, the risk is especially high because petals are delicate, densely layered, and often held close together, creating small pockets of stagnant air where moisture lingers.
Finding spots on flowers you have tended for weeks is frustrating, especially when they looked clean at harvest. Spores can be present on debris and plant surfaces before obvious symptoms appear. A wet period gives infection a chance to develop, and the damage may only become visible during storage or delivery. The Spring Greenhouse Checklist for Producing Strong, Market-Ready Cut Flowers helps you check the production steps that come before that disappointment.
UMass Extension’s cut-flower Botrytis guide describes infection conditions involving a moisture film for 8–12 hours, relative humidity of at least 85%, and temperatures around 13–18°C. Treat these as a warning about a combination of conditions, not a promise that one reading below 85% makes the crop safe. Duration and the actual petal surface matter.

Core Climate Moves That Reduce Botrytis Pressure
Good humidity management is not a single adjustment. It is a sequence of small, coordinated actions: heating, venting, air circulation, irrigation timing, spacing, sanitation, and postharvest handling. Each reduces moisture where Botrytis needs it most.
- Vent before the crop reaches saturation. Small vent openings, used early enough, can exchange moisture-laden air for drier outside air before condensation forms. Waiting until the greenhouse is visibly wet is too late.
- Use heat to create carrying capacity. Warm air can hold more moisture. A brief, controlled heat input, paired with ventilation, can lift moisture from the canopy and remove it from the house.
- Keep air moving horizontally. Horizontal airflow fans help break up cold, stagnant pockets and reduce microclimates inside dense flower canopies. The aim is gentle, continuous mixing, not harsh wind.
- Water early in the day. Irrigation that leaves foliage, floors, or media surfaces wet late in the afternoon adds to night humidity. Morning watering gives the crop and greenhouse structure time to dry before dusk.
- Open the canopy when possible. Correct spacing, timely disbudding, removal of senescent leaves, and disciplined crop work improve air movement around stems and buds.
- Remove infected or dead tissue promptly. Botrytis sporulates readily on aging petals, leaf debris, and cull piles. Sanitation lowers the background spore load that humidity can activate.
- Coordinate greenhouse and cooler conditions. Harvest dry flowers and avoid trapping moisture in sleeves. Cold flowers exposed to warm, humid air can collect condensation; plan transfers as carefully as the storage temperature.
Heating and Venting: The Classic Dehumidification Pair
Heating lowers relative humidity at the same water-vapour content, but it does not remove that water. Ventilation exchanges air; a correctly sized dehumidifier removes water by another route. Choose a system that can handle the crop’s moisture load without pushing temperature outside its growing requirements. The useful question is where the water goes, not simply whether the humidity display has fallen.
Watch the transition after sunset and the period before dawn. Leaves and petals can be cooler than the air measured by a nearby sensor, so condensation may occur in one part of the crop while the house average looks acceptable. UMass explains these canopy effects in its guide to reducing greenhouse humidity. Compare canopy readings with the control sensor before changing setpoints.
Coordinate thermal screens, vents and heating controls rather than copying a fixed gap or timer from another greenhouse. The right sequence depends on your equipment and weather. Have a qualified technician check combustion-heater and extractor interactions: a humidity adjustment should not draw exhaust into the growing area.
Irrigation, Floors, and Hidden Moisture Sources
Walk the house after irrigation. A leaking connector, puddle beneath a bench or wet aisle may be a manageable moisture source that the climate computer cannot explain. Repair leaks and clear drainage before compensating with more heat. Water held in the substrate is part of the balance too; look at how long it stays wet between irrigations.
Drip irrigation and subirrigation can reduce leaf wetness compared with overhead watering, but they do not eliminate humidity risk. Wet media and transpiring foliage still load the greenhouse air with moisture. Irrigation should be matched to crop demand, light level, root health, and substrate, rather than applied by habit. A related piece, “Greenhouse Climate Mistakes That Reduce Cut Flower Quality”, looks at this from another side.
If symptoms continue despite those changes, ask a plant-diagnostic service to identify the problem. Cornell University is one starting point for finding university horticulture and plant-disease resources. A photograph of brown petals alone cannot reliably distinguish Botrytis from every other cause of damage. Keep samples and notes from affected and apparently healthy blocks.

When Fungicides Fit Into the Program
If treatment is needed, work from a confirmed diagnosis and a crop-specific programme. Repeatedly applying a product while petals remain wet leaves the underlying problem in place. Ask your crop adviser about suitable registered options and resistance management; the right product and timing depend on the crop, location and production system.
Always follow local regulations, label directions, resistance-management guidance, re-entry intervals, and crop-safety precautions. The most durable program combines environmental control, hygiene, resistant or less susceptible cultivars where available, and targeted treatments. The Royal Horticultural Society provides a clear general overview of gray mold biology and cultural control principles for ornamental plants.
A short evening check that helps the morning shift
My practical tip: record three things together before leaving—the crop block, whether petals are visibly dry, and the climate action you have taken. A note saying “north bench damp after irrigation; leak repaired; check before sunrise” is easier to act on than “humidity high”. Add the time so the next person can compare it with the overnight record.
Review one affected block alongside a cleaner block of the same crop. Check density, sensor position, irrigation finish time and debris beneath the benches. Change one manageable cause, record what happened and keep inspecting. This makes the next decision clearer than adjusting several settings at once. For the hours after cutting, use the post-harvest care guide and the explanation of why cut flowers wilt early.
Common questions
What humidity level prevents Botrytis in cut flowers?
There is no single universal number because risk depends on temperature, crop density, airflow, flower species, and duration of wetness. As a practical principle, avoid sustained near-saturated air and prevent condensation on petals. Many growers manage night climate to keep the crop safely away from dew point rather than chasing one fixed relative humidity target.
Do fans alone control Botrytis?
Fans help by reducing stagnant microclimates, but they do not remove moisture from the greenhouse. If the air is already saturated, circulation simply moves humid air around. Fans work best with heating, venting, appropriate irrigation, and canopy management.
Should infected flowers be removed immediately?
Yes. Infected blooms, fallen petals, and dead leaves can produce spores and raise disease pressure throughout the house. Remove them carefully, place them in covered containers, and dispose of them away from production areas. Avoid carrying diseased material through clean crop zones when flowers are wet.
Can Botrytis appear after flowers have been shipped?
Yes. Latent infections or spores on damp petals may develop during cooling, transport, retail holding, or vase life. That is why greenhouse humidity control, dry handling, clean buckets, rapid cooling, and moisture-conscious packaging are all part of producing cut flowers that remain beautiful after harvest.